Network Appliance NS0-526 問題集

質問 1：
You are asked to size an ONTAP disaster recovery and backup cluster. You are required to use 4 x 40 Gb Ethernet ports per controller and 4 x 32 Gb FC ports per controller. You also need to confirm support for Commvault IntelliSnap for NetApp v11.
Inthis scenario, which two tools would confirm these requirements? (Choose two.)
A. Active IQ
B. Hardware Universe
C. Interoperability Matrix Tool
D. OneCollect
正解：B,C

質問 2：
Click the Exhibit button on the right.

You have an AFF A300 controller with four volumes in the aggregate that is shown in the exhibit. You replicate all four volumes to one aggregate on a FAS8200 controller in a different cluster.
Referring to the exhibit, what are the storage efficiency savings on the destination FAS8200?
A. 2:1
B. 4.28:1
C. 1.5:1
D. 5.78:1
正解：D

質問 3：
You recently set up a SnapMirror relationship with a daily update schedule. You want to verify that the updates are being performed daily.
Which two actions inside OnCommand System Manager would you ensure that the SnapMirror transfers are occurring daily? (Choose two.)
A. In the Jobs window, verify that all manual Snapshot copy operations have completed in the past 24 hours.
B. In the Relationships window, verify that the relationship state was broken in the past 24 hours.
C. In the Jobs window, verify that all SnapMirror jobs have completed within the past 24 hours.
D. In the Relationships window, verify that the lag time is less than 24 hours.
正解：C,D

質問 4：
You are upgrading your Data ONTAP cluster from clustered Data ONTAP 8.3 to clustered Data ONTAP 9.1.
Which two actions mustbe performed for the SnapMirror relationships? (Choose two.)
A. After the upgrade, resynchronize, and resume SnapMirror relationships.
B. Delete and re-create SnapMirror relationships.
C. Break existing SnapMirror relationships.
D. Delete the obsolete SnapMirror Snapshot copies which were created in Data ONTAP 8.3.
正解：A,C

質問 5：
You want to set up protection relationships at the time of provisioning one or more primary volumes in the source cluster in ONTAP.
Which NetApp management tool enables you to accomplish this task?
A. ONTAPCLI
B. SnapCenter
C. OnCommand Unified Manager
D. OnCommand System Manager
正解：D

質問 6：
Click the Exhibit button.

Your customer wants to protect a volume and replicate it to a secondary volume. The customer has tried to configure this relationship using OnCommand System Manager. Upon reviewing this newly configured relationship, you discover that the configuration does not satisfy the customer's stated requirements.
Referring to the exhibit, what should you do to ensure that the volume is protected?
A. Initialize the relationship.
B. Change the schedule to hourly.
C. Delete the relationship and recreate it.
D. Resynchronize the relationship.
正解：C

質問 7：
You have multiple load-sharing destinations for a volume in a storage virtual machine. The source volume has become unavailable and you want to make one of the destination volumes the new source.
What happens to the original source volume?
A. The original source volume goes offline.
B. The promoteoperation takes the original source volume offline.
C. The promote operation deletes the original source volume.
D. The initialize operation deletes the original source volume.
正解：C

質問 8：
A customer is running clustered Data ONTAP on primary and secondary clusters. The customer is using SnapVault to back up volumes between the clusters.
The customer has good Data ONTAP7-Mode knowledge and needs to set up two new SnapVault relationships between the clusters on a weekly schedule.
Which solution would you recommend to satisfy this requirement?
A. Use OnCommand System Manager.
B. Use the node shell command line interface.
C. Use the system shell command line interface.
D. Use OnCommand Workflow Automation.
正解：A