Network Appliance NS0-506 問題集

質問 1：
Which three environmental or physical requirements need to be met when designing a SAN solution? (Choose three.)
A. power
B. clustered Data ONTAP version
C. rack space
D. cooling
E. IOPS
正解：B,C,E

質問 2：
Which two flags would you use to enable NetApp thin provisioning on a LUN? (Choose two.)
A. -space-reserve disabled -space-allocation enabled
B. -space-reserve disabled -space-allocation disabled
C. -space-reserve enabled -space-allocation enabled
D. -space-reserve enabled -space-allocation enabled
正解：B,C

質問 3：
What is installed on your Linux host when you install the Linux Unified Host Utilities 7.0?
A. SAN Toolkit data collection utility
B. nSANity
C. software iSCSI initiator
D. drivers and firmware
正解：A
解説: (Topexam メンバーにのみ表示されます)

質問 4：
Which command enables the FC protocol on clustered Data ONTAP?
A. vserverfpolicy enable -vserver<node_name> -policy -name <policy_name> -sequence- number <seq_num>
B. node run node <node_name>fcadmincongig -e
C. vserverfcp create -vserver<vserver_name> -status -adain up
D. vserveriscsi create-vserver<vserver_name> -target -alias <vserver_name>
正解：C
解説: (Topexam メンバーにのみ表示されます)

質問 5：
Click the Exhibit button.
cl01::>ucadmin show
Current Current Pending
Pending Admin
Node Adapter Mode Type Mode
------------- ------- -------
--------- -------- --------- -
----------
cl01-01 0c fc target - -
online
cl01-01 0d fc target - -
online
cl01-01 3a cna target - -
online
cl01-01 3b cna target - -
online
cl01-01 4a cna target - -
online
cl01-01 4b cna target - -
online
cl02-01 0c fc target - -
online
cl02-01 0d fc target - -
online
cl01-02 3a cna target - -
online
cl01-02 3b cna target - -
online
cl01-02 4a cna target - -
online
cl01-02 4b cna target - -
online
12 entries were displayed.
cl01::>
Referring to the exhibit, which cables are valid for connecting port 0d on node cl01-02 when the switch is 10 meters
away?
A. LC/LC optical OM3 cables
B. Twinax copper SFP+ passive cables
C. RJ45 Cat6 Ethernet cables
D. Twinax copper SFP+ active cables
正解：B

質問 6：
You have an iSCSI host that is unable to connect to an SVM named svm1 over a LIF name lif1. The home node and port
of lif1 is port e0e. The event log show command displays the error ISCSI:
network interface disabled for use; incoming connection discarded.
Which command would you use to resolve the problem?
A. iscsi interface enable -vserver svm1 -lif lif1
B. broadcast-domain add-ports -broadcast-domain iscsi -ports cI01-01:e0e
C. network interface modify -vserver svm1 -lif lif1 -failover-group Default
D. vserver iscsi create -target-alias svm1 -status-admin up -vserver svm1
正解：A

質問 7：
A customer has recently deployed a clustered Data ONTAP 8.3 system and is trying to mount LUNs to a Windows 2012
Server using the iSCSI protocol. They are using Cisco Nexus 5548 network switches and the network administrator has
informed the storage administrator that the ports are set to switchport mode trunk. The storage administrator has
also been informed that the host and storage should be using VLAN 400 for iSCSI traffic. When the storage
administrator attempts to add the SVM as an iSCSI target, it fails to connect.
What is causing the problem?
A. The storage administrator has not enabled VLAN tagging on the storage ports.
B. Windows 2012 Server does not support the iSCSI protocol on a VLAN tagged interface.
C. Clustered Data ONTAP 8.3 does not support running iSCSI on a VLAN ID below 1024.
D. Clustered Data ONTAP 8.3 does not support the iSCSI protocol on a VLAN tagged interface.
正解：A

質問 8：
You recently configured your SVM to serve data with the FC protocol by issuing the following commands:

However, your LIF still shows an operational status of down.
What must you do to change the operational status to up?
A. Add the LIF to a igroup.
B. Create a LIF on the node's HA partner.
C. Configure zoning on the switch.
D. License and enable the FC service.
正解：D
解説: (Topexam メンバーにのみ表示されます)