Dell DCAPE-100 問題集

質問 1：
A technician needs to add a server as a host to an existing VMware environment. The server has 2x 1Gb LOM ethernet ports and a 4-port 1Gb Broadcom NIC. The 2 LOM ports are teamed to be used as SAN connections. All active data and management traffic should utilize the 4x 1Gb ports on the Broadcom NIC. The technician needs to achieve management and data redundancy at the hardware level to handle a single port failure.
What is the most effective way to meet this requirement?
A. Partition the ports using NPAR in the system BIOS
B. Connect the 4x 1Gb ports to a load balancer
C. Buy an additional 10Gb NIC for the server
D. Team the ports together in the OS
正解：C

質問 2：
Refer to the exhibit.

A technician is testing basic SMTP alerts on an iDRAC for a server. The test SMTP alerts fail with the message shown. The technician can ping the hostname of the SMTP server from their workstation.
Which two actions should the technician take to fix the issue? (Choose two.)
A. Use the IP address of the SMTP server
B. Add iDRAC hostname to the SMTP server hosts file
C. Verify SMTP port settings on the iDRAC
D. Enable the SMTP Client service on the iDRAC
正解：A,D

質問 3：
A technician configures iDRAC on a new server for access on the management network.
When accessing via telnet, the connection is refused. Network connectivity is a verified network. NO ports are blocked by any network devices.
Why is the telnet connection being refused?
A. Telnet is NOT enabled by default on the iDRAC
B. The telnet client must be configured to connect to port 8899 on the iDRAC
C. Telnet is NOT supported to access iDRAC.
D. The iDRAC must be configured to allow the IP address of the technician's workstation.
正解：A

質問 4：
A technician has received a new server with 5 drives and needs to configure the drives into a specific configuration as provided by the administrator.
The administrator will also add additional disks as separate raid arrays at a later date.
*Drive 0 is passed through to the OS (to be managed by the OS)
*Drives 1-3 as a RAID 5 with drive 4 as a hotspare just for this newly created RAID 5 How should the technician do this in the PERC BIOS?
A. Set drive 0 to Ready, set drives 1-3 as a RAID 5, and drive 4 as a Dedicated Hot Spare
B. Set drive 0 to Ready, set drives 1-3 as a RAID 5, and drive 4 as a Global Hot Spare
C. Set drive 0 to Non-Raid, set drives 1-3 as a RAID 5, and drive 4 as a Dedicated Hot Spare
D. Set drive 0 to Non-Raid, set drives 1-3 as a RAID 5, and drive 4 as a Global Hot Spare
正解：A

質問 5：
A technician needs to initially configure a server from a bare metal condition in the following areas:
* Processor settings
* Disk configuration
* iDRAC network settings
The technician can only reboot once to achieve these tasks.
Where should the technician configure these settings? (Choose three.)
A. System BIOS
B. PERC Configuration Utility
C. PXE Settings
D. iDRAC Settings
E. Device Settings
正解：A,B,C

質問 6：
A server is configured with a RAID 5 Virtual Disk across 5 hard disks and 1 spare disk. If a hard disk failure occurs within the RAID 5 virtual disk, the spare disk needs to be online as quickly as possible. It is acceptable for users to experience decreased performance during the rebuild procedure.
How should this requirement met?
A. Select Fast Rebuild
B. Enable Rebuild Priority
C. Change cache to Write Through
D. Increase Rebuild Rate
正解：D