SAP C_TSCM44_65 問題集

質問 1：
Within the global parameters and default values the "plan explosion" is set to "explode production process model (PPM)".
Your master data team would like to switch from PPM to PDS over the next 12 months as part of an ongoing redesign project.
Is it possible to configure the system to explode the PDS for product "A" yet still explode the PPM for product "B"?
A. No. The master data project has to be harmonized with the APO planning project that is already implemented. A big bang date has to be planned for the change of the "plan explosion".
B. Yes. As soon as a PDS is integrated via the CIF, the corresponding APO product master is overruled to the value "explode PDS". These products will then be planned with PDS against the global value "explode PPM".
C. No. Since the SNP planning module could also be in use, the plan explosion always needs to be consistent, not only for all products but also across both APO planning modules.
D. Yes. In model and version management you have to define the product-specific master data explosion. As soon as a PDS is generated in ECC, the APO system uses this new master data.
正解：B

質問 2：
Why do you need to create planned independent requirements (PIRs) based on DP forecast data?
Note: There are 3 correct answers to this question.
A. For planning in SNP or PP/DS
B. For transferring to SAP ECC Demand Management for ECC MRP planning
C. For the CTP check
D. For the GATP check against ATP time series
E. For the GATP check against PIRs
正解：A,B,E

質問 3：
The customer asks about bucket-oriented CTP. How do you explain bucket-oriented CTP correctly?
A. It schedules against bucket capacity instead of confirming against time-continuous capacity.
B. It uses lot size rounding profiles to calculate bucket quantities instead of scheduling lot-for-lot.
C. It allows confirmation against SNP capacity key figures.
D. It summarizes all requirements within a predefined bucket and does not confirm individual requirements.
正解：A

質問 4：
In what situations do you use SAP SCM APO instead of SAP ECC PP? Note: There are 3 correct answers to this question.
A. When dependent requirements need time stamp information
B. When enhanced capacity planning capabilities are needed
C. When the low-level-code calculation is needed for all BOM structures
D. When MRP planning logic is mandatory during a planning run
E. When alert messages need to be updated in a planning session that has not been saved
正解：A,B,E

質問 5：
The customer needs an SNP planning area for time-dependent safety stocks and scheduling agreements.
As well as maintaining a time-dependent safety stock method in the product master, what else do you have to do?
A. Copy planning area 9ASNP03 with planning object structure 9ASNPSA into a customer-specific planning area and add an auxiliary key figure in the data view.
B. Copy planning area 9ASNP02 with planning object structure 9ASNPBAS into a customer-specific planning area and add a time series key figure.
C. Copy planning area 9ASNP02 with planning object structure 9ASNPBAS into a customer-specific planning area and add an auxiliary key figure in the data view.
D. Copy planning area 9ASNP03 with planning object structure 9ASNPSA into a customer-specific planning area and add a time series key figure.
正解：D

質問 6：
You can select PP/DS PDS instead of PP/DS PPM to integrate a process with APOPP/DS.
Which of the following standard ECC functions require the PP/DS PDS for the integration?
Note: Configuration scheme VC is used.
Note: There are 3 correct answers to this question.
A. Variant configuration of sales orders
B. PP-SFC (shop floor control)
C. Order BOM
D. PP-PI (process industries)
E. Engineering change management
正解：A,C,E

質問 7：
Using the APO Core Interface, which of the following ECC master data objects are mapped to APO locations?
Note: There are 3 correct answers to this question.
A. Production line
B. Distribution center
C. Work center
D. MRP area
E. Vendor
正解：B,D,E

質問 8：
You want to set up GATP in the SCM system.
How can you reuse the existing ATP Customizing from the ECC system?
A. Transfer the ATP Customizing from the ECC system into the SCM internal BW and then load the Customizing tables from BW to the SCM system.
B. Download the ATP Customizing from the ECC system into a flat file and then upload it directly into the SCM system using predefined transfer structures.
C. Run a report in the SCM system that extracts the ATP Customizing data from the ECC system and loads it into the Customizing tables in the SCM system.
D. Use a data channel in the core interface, create an integration model, and transfer the ATP Customizing from the ECC system to the SCM system.
正解：D