Avaya 6101.1 問題集

質問 1：
When configuring Ethernet Routing Switch (ERS) 8600 using the default interface, the attempt to load an ACLI configuration fails because the default interface is the CLI.
How is the ACLI interface obtained?
A. Change the ACLI boot flag and save the boot configuration file.
B. Use the abort command and enter "no" at the default interface prompt
C. Change the interface type in the config.cfg file.
D. exits the CLI and chooses ACLI at the interface manager prompt.
正解：D

質問 2：
A network has some Ethernet Routing Switch (ERS) 5500 switches licensed at the advanced level for Release 6 2 A technician implementing Protocol independent Multicast
-
Sparse Mode (PIM-SM) Which licensing requirement applies?
A. the PIM-SM is included m the base license with release 6.2
B. the PIM-SM con only be licensed on ERS 5510 models
C. the PIM-SM is already covered by the existing advanced feature license
D. A Premier license is needed
正解：A

質問 3：
A technician is configuring a Link Aggregation connection from a stack of Ethernet Routing Switch (ERS) 5500 lo a core pair of ERS 8600 switches.
Which statement about the correct uplink configuration is true?
A. Distribute uplinks across different ERS 5500 switches in the stack.
B. Enable Spanning Tree Protocol for the MLT when using it with SMLT in the core of the network.
C. Disable auto negotiation and replace it with VLACP to identify single fiber fault failure
D. Use unique MLT IDS for each stack of edge ERS 5500 switches
正解：A

質問 4：
A customer has purchased some Ethernet Routing Switch (ERS) 5600 switches must integrate two ERS 5600 units into existing stack of ERS 5500 switches.
What is the procedure for the integration of the new ERS 5600?
A. Remove the AC from the stack, integrate the two ERS 5600 units into the existing 5600 set to "base unit" and one ERS 5600 set to "non base unit" set the existing ERS 5500 base unit to "non base unit" apply power to stack.
B. With power applied to the stack, integrate one ERS into the stack as non base unit in mixed stack operational mode. Change the existing ERS 5500 base unit to "non base unit" and set the new 5600 to "base unit". Reboot the stack integrate the second ERS 5600 in mixed stack operational mode.
C. With power applied to the stack, integrate one ERS into the stack as non base unit in mixed stack operational mode. After the two ERS 5600 units have obtained their configuration from the ERS 5500 base unit, change the ERS 5500 to "non base unit" and set one ERS 5600 to "base unit". Reboot the switch stack.
D. with power applied to the slack, change the existing ERS 5500 base unit to "Non Base Unit" in mixed stack operation Integrate the two new ERS 5600 to the stack with them set as "Base Unit" in mixed stack operation Reboot the stack.
正解：C

質問 5：
Which command mode contains the commands needed to work on software licenses?
A. Global Configuration
B. Privileged Exec
C. User Exec
D. Software Configuration
正解：C

質問 6：
What is the front panel port configuration for the Ethernet Routing Switch (ERS) 2550TPWR?
A. 50 10/100BaseT ports (PoE on 25 ports) two combo 10/100/1000BaseT or SFP port
B. 48 10/100 BaseT ports (PoE on 48 ports) Two combo 10/100/1000BaseT or SFP port
C. 48 10/100BaseT ports (PoE on 24 ports) two combo 10/100/1000BaseT or SFP port
D. 50 10/100BaseT ports (PoE on 50 ports) two combo 10/100/1000BaseT or SFP port
正解：C

質問 7：
After experiencing issues with XFPs, the show sys pluggable-optical-modules into CLI command is used to find that the switch does not recognize the XFPs.
Which other method can be used to view the XFP compatibility?
A. Show DWDM-XFP {detail}
B. Check for port alarms
C. Config sys set pluggable-optical-module. Info
D. select Edit, port, General, DDI/SFP from the Enterprise Device Manager to see the XFP port specifics_
正解：D