Avaya 3605 問題集

質問 1：
After issuing a show mlt list stats (CLI) or show ist Stat (ACLI) command, it is determined that the running type is normal MLT and not 1ST. What are two causes of the IST not running properly? (Choose two)
A. The peer IP address is not the address of the peer switch IST VLAN.
B. The IST is not enabled on both switches.
C. The MLT ID does not match on both switches.
D. The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.
正解：A,C

質問 2：
The Ethernet routing switch (ERS) 5000 switches are being upgraded and it appears that a license is not recognized on the switch. Which two statements are valid
sources
of
information
that will help
resolve
the
license
installation? (Choose two.)
A. Check the record of MSG address changes
B. Use the show license file command to get the license installation status.
C. Check to see if the MAC address is correct in the license file.
D. Use the show license command to get the license installation status
E. Check for an 'invalid license fife' log report
正解：C,D

質問 3：
Refer to the exhibit.

When checking an Inter Switch Trunks (IST) configuration using the show mlt ist info command as shown in the exhibit, which IP address should be in the IP ADDRESS column?
A. The IP address of the IST VLAN on the local switch.
B. The IP address of the first IST port on the peer switch.
C. The IP address of the IST VLAN on the peer switch.
D. The management IP address of the peer switch.
正解：C

質問 4：
Refer to the exhibit.
A campus network has been established with four Ethernet Routing Switch (ERS) 8600 switches in a switch cluster, two pairs with an Inter Switch Trunks (IST) running Split Multi Link Trunk (SMLT) and Routed Split Multi-Link Trunking (RSMLT). The traffic filters are required to block specific source IP addresses to be forwarded through the core. With reference to the exhibit, how should these filters be set up?
A. Configure and apply all the filters on the two core IST links only
B. Configure the filters on the ports first and then the IST.
C. Apply the filters to all ports that receive traffic from outside the immediate switch cluster.
D. Configure the filters on the 1ST first before any other ports.
正解：C

質問 5：
A technician is implementing a new network that contains eight Ethernet routing switch (ERS) 8600 switches and uses advanced features. Where are two possibilities for generating license? (Choose two)
A. one multi-chassis license using multiple MAC addresses
B. one premier feature license for the network
C. one individual advanced feature license for each ERS 8600 chassis
D. one site license per ERS 8600
E. one advanced feature license for the network
正解：D,E

質問 6：
When configuring a new Ethernet Routing Switch (ERS) 8000 using the default interface, the attempt to load an ACLI configuration fails because the default interface is the CLI. How is the ACLI interface obtained?
A. Change the ACLI boot flag and save the boot configuration file.
B. Change the interface type in the config.cfg file.
C. Exit the CLI and choose ACLI at the interface manager prompt.
D. Use the abort command and enter 'no' at the default interface.
正解：C

質問 7：
After issuing a show ist stats (CLI) or show ist stat (ACLI) command, it is
determined that the running type is normal MLT and not inter Switch Trunks?
(Choose two)
A. The Peer IP address is not the address of the Peer switch IST VLAN.
B. The MLT ID does not match on both switches.
C. The IST is not enabled on the both switches.
D. The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.
正解：A,C

質問 8：
Which set of procedures will upgrade the boot monitor on an Ethernet Routing Switch (ERS) 8600 with a single 8692SF module?
A. Copy the new image to flash. Activate the new image with SF module in service.
B. Copy the new image to flash. Modify the boot choice for run-time change. Activate the new image SF module in service.
C. Copy the new image to flash. Boot the new image.
D. Copy the new image to flash. Modify the boot choice for run-time image. Boot the new image.
正解：C