VCE 220-010 問題集

質問 1：
Which two components are part of the Vblock@ System infrastructure? (Choose two)
A. Production application software
B. Network switches
C. Database software
D. Storage array
正解：A,C

質問 2：
How do you create a log bundle for the Nexus 1000V virtual switch module (VSM)?
A. Run the show tech-support svs > bootflash:techsupport.log command from the VSM shell.
B. Use the Java-based Nexus 1000V log bundle creator on the element manager.
C. Use the vCenter client to generate a VMware support bundle.
D. Execute the vem-support all command from the shell on each ESXi host.
正解：A

質問 3：
Your Vblock@ System 720 was set up with a FAST VP policy of 100% EFD, 100% FC, with 100% SATA, and then applied the policy to all the storage groups. You have allocated all thin LUNs from the Fibre Channel pool and would like to ensure that all but 10% of the EFD drives can be used by the FAST policy.
Which setting would you use to accomplish this task?
A. Adjust the Pool Reserved Capacity to 10.
B. Adjust the Relocation Rate to 10.
C. Adjust the compression rate to 10.
D. Adjust the Data Movement Mode to 10.
正解：A

質問 4：
While troubleshooting a VCE Vision Intelligent Operations problem, you notice that the rsyslog file was empty.
Which action should you perform first?
A. Start an SSH session to the VCE Vision software system library and verify the FMagent status.
B. Start an SSH session to the VCE Vision software system library and verify the service status.
C. Log on to the Vision GUI, and run a compliance report.
D. Log on to the vSphere Web Client and verify that the VCE Vision software system library was installed.
正解：B

質問 5：
You are asked to permanently shrink a vSphere cluster from five nodes to four nodes. You confirm that all five ESXi hosts are at less than 20% utilization. You also confirm that VMware DRS is properly configured and running on the cluster.
Which procedure should be followed to shrink the cluster?
A. In vCenter, put the ESXi host into maintenance mode, remove the host from the cluster; in UCSM, stop the server then delete the service profile.
B. In UCSM, stop the server then delete the service profile; in vCenter, put the ESXi host into maintenance mode, remove the host from the cluster.
C. In UCSM, stop the server then delete the service profile; in vCenter, delete the host.
D. In vCenter, put the ESXi host into maintenance mode, remove the host from the cluster; in UCSM, stop the server then disconnect the service profile.
正解：A

質問 6：
What is the UCSM concept that confirms associated blade server hardware has the required configuration?
A. Templates
B. Service profiles
C. Server pools
D. Resource pools
正解：B

質問 7：
Which management application is used to discover the Cisco MDS switches in the network?
A. UIM
B. DCNM
C. UCSM
D. Unisphere
正解：B

質問 8：
Your company needs to add a new masking view to their Vblock@ System 720.
Which three grouping constructs must be selected? (Choose three)
A. Storage group
B. Initiator group
C. Port group
D. Device group
E. Disk group
正解：A,B,C

質問 9：
You are working with VCE Support and are asked to send the complete support log bundle for your MDS switch.
Which statement describes what you should do?
A. Connect to the MDS switch and run the show tech-support detail command.
B. Connect to the MDS switch and run the show zone analysis vsan command.
C. Connect to the MDS switch and run the show flogi command.
D. Connect to the MDS switch and run the show accounting log command.
正解：A